Difference between revisions of "Yeast Chemical Transformations"
From PombEvolution
Jump to navigationJump to searchLine 23: | Line 23: | ||
# Incubate at RT for ~16h | # Incubate at RT for ~16h | ||
# Spin down the cells at 1600 x g for 3 min, RT and remove supernatant | # Spin down the cells at 1600 x g for 3 min, RT and remove supernatant | ||
− | # Resuspend cells in 100 μl water and spread them on [[YES - Yeast Extract Supplemented | YES]] plates with appropriate selective agent (1 in 1000 [[Nourseothricin]] (100 μg/μl) or 1 in 500 G418 (50mg/ml)). | + | # Resuspend cells in 100 μl water and spread them on [[YES - Yeast Extract Supplemented | YES]] plates with appropriate selective agent (1 in 1000 [[Nourseothricin]] (100 μg/μl) or [[Hygromycin]] (100 μg/μl) or 1 in 500 G418 (50mg/ml)). |
# Incubate at 32°C for at least 4 days (more likely longer) | # Incubate at 32°C for at least 4 days (more likely longer) | ||
Revision as of 09:41, 16 May 2019
Protocol based on Rodríguez-López et al. 2017
Chemically competent cells are available for some pombe strains in 50μl aliquots in the -80°C. If other strains are required, use the protocol Synchronized Competent Yeast Cells.
Chemical transformation
- Thaw by heating (use the 43°C bath) and then put on ice:
- Thaw Competent fission yeast cells quickly for 30 sec to RT in waterbath and put on ice
- Thaw on ice:
- HR template dsDNA e.g. produced by PCR (if frozen)
- Add to the competent cells in this order:
- 2 μl ssDNA (mix by carefully flicking the tube)
- 5-20 μl HR template produced by PCR. Amount depends on template concentration and also on strains used. Not-labstrain transforms much less good.
- Add 115 μl PEG4000 (i.e. 2 volumes) and mix by pipetting up and down a few time
- Immediately incubate for 15min @ 43°C.
- Spin down the cells at 1600 x g for 3 min, RT and remove supernatant
- Remove supernatant and re-suspend the cells in 1 ml
- Reduce the added supplements (e.g. leucine, adenine etc) to 10% of the standard amount.
- Incubate at RT for ~16h
- Spin down the cells at 1600 x g for 3 min, RT and remove supernatant
- Resuspend cells in 100 μl water and spread them on YES plates with appropriate selective agent (1 in 1000 Nourseothricin (100 μg/μl) or Hygromycin (100 μg/μl) or 1 in 500 G418 (50mg/ml)).
- Incubate at 32°C for at least 4 days (more likely longer)
CRISPR/Cas9 transformation
This is the same protocol as above, only the added DNA and amount of PEG4000 added differs.
- Thaw by heating (use the 43°C bath) and then put on ice:
- Thaw Competent fission yeast cells quickly for 30 sec to RT in waterbath and put on ice
- Thaw on ice:
- HR template repair DNA
- sgRNA plasmid (concentration should be ~200ng/μl)
- Add to the competent cells in this order:
- 2 μl ssDNA (mix by carefully flicking the tube)
- 10 μl HR template
- 10 μl sgRNA plasmid
- Add 145μl PEG4000 and mix by pipetting up and down a few time
- Immediately incubate for 15min @ 43°C.
- Centrifuge the cells at 1600 x g for 3 min at room temperature (RT).
- Remove supernatant and re-suspend the cells in 1 ml. When adding supplements (e.g. leucine, adenine etc) reduce these to 10% of the standard amount.
- Incubate at RT for ~16h
- Spin down the cells at 1600 x g for 3 min, RT and remove supernatant
- Resuspend cells in 100 μl water and spread them on YES plates with 100 μg/ml Nourseothricin.
- Incubate at 32°C for at least 3 days (or even longer!)